Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello. In my application I am using nRF5 SDK 15.2.0 9412b96. I am trying to communicate with two devices on two different SPIM instances. The first device is a DW1000 radio...
Dear Sir:
We observed that everytime we use OTA to update the firmware of the nRF52, the 6Byte address will change, just minus 1 compared with before, such as
FC:AE:3F...
I am using the software PWM library (SDK12.0) with the DRV8834 to drive a bipolar stepper motor. Although the motor is working in both directions with the code below, the...
Hi, I want to make sure that all application data are erased when we do a DFU, so that the newer application get a clean start without having to worry about data from older...
For nRF9160, is there an overview of the builtin CA certificates?
I have now deleted all certificates I added manually with:
int nrf_inbuilt_key_delete(nrf_sec_tag_t sec_tag...
We are using NRF52832 with SDK15.0 to develop a wearable device that collects data every 10 seconds. It works fine except that NRF52832 shuts down automatically 1 hour after...
Hi
My SPI Master wraps SPI comms using a couple of additional logic lines nReadFromSlave (Master Output) and nSlaveReady (Master Input).
It treats an SPI transaction as...
Hi, everybody. I have a Thread mesh network (wireless) running multiple nodes. I am using the CLI to send pings between the nodes and i analyze the mesh performance. My problem...
Hi there!
The documentation defines two possible return values for sd_rand_application_vector_get : NRF_SUCCESS and NRF_ERROR_SOC_RAND_NOT_ENOUGH_VALUES . I am wondering...
Hello,
I use ble_thread_dyn_mtd_scanner with BLE beacons but there is never any advertising received ?
If i check with my smartphone, they are detected.
Any idea please...
Hi,
How do you recommend to analyze nrf52840 dongle power consumption?
What I have is:
Nrf52840 dongle
Nrf52DK
Nrf6707 profiler kit
How can these be used together...
I am looking for a .hex file application for the nrf52840 dk that I can control from an external application via the USB port in order to setup and test the physical layer...
HI, Im developing a custom board (NRF58232) with a bmx055 connected by TWI.
I have used the twi_scanner and twi_sensor and all OK, It was working !
But now I want to use...
From what I can tell, the SDK for Thread provided from Nordic uses a precompiled Openthread library that hardcodes the UART pin configuration. This means that users of this...
I'm developing on the nRF52840, SDK15, and s140 v6.0. I'm trying to use the sd_power_gpregret_set() function to write a value that would then be read after reset to start...
