Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
Our application requires that we connect a nRF52832 to a Microchip PIC32MZ host via the Nordic parts UART (RS-232 at CMOS levels).
In a previous application, we...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
Im having some issues with my nrf52 DK board, the jLink firmware seems to be buggy, I installed the latest available (160212) manually, but the j-link tool keeps bugging me...
SDK 9.0.0 sd s110
I want bootloader to store some persistent data at the APP DATA location. while going through the bootloader(dual_bank_ble_s110) source code, i noticed...
I have never worked with BLE devices before. Now I have a BLE project where I must be able to do he following:
I want to be able to pair/bond my BLE device to a smartphone...
chip N51822QFAACO
s110_nrf51822_5.2.1_softdevice.hex
keli 5
\nrf51_sdk_v4_4_2_33551\nrf51822\Board\pca10001\ble\ble_app_proximity\
works fine
nrf51_sdk_v5_2_0_39364...
Hello Everyone
I have designed my custom board using nrf51822 i have tested the votlage rating, on the VDD pins everything is fine (3v) but the real problem is my antenna...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
