hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
Hi,
I have downloaded the new version of SDK (v.5.0) today and just tried your experimental ble_app_ancs (no modifications) but it seems it asserts with error_code=0xB...
Hi,
I need to know when to use the write_wo_resp property for a characteristics, and what is the difference between write and write_wo_resp property of a characteristics...
I've read a post from Marc Nicholas about the attempt to port the entire gcc toolchain under Xcode on Mac OS X.
As I wrote in another post, I've the entire gcc toolchain...
I'm getting started with this evaluation kit by working through the user guide and almost made it through the Blinky example before I ran into trouble.
After compiling...
We have some hardware versions of the Nrf51822: build BA, CA.
Is the new S110 v6.0.0 softdevice compatible with these hardware versions?
If it is not compatible, wich...
Hi.
Using 51822 with BLE stack, I was faced with the problem of low transfer rates (5kb) on my android device (phone). It is very slow.
Can work 51822 with standart...
Can I initial like below to generate 2 opposition PWM waves on 2Pins？
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer 2 COMPARE[0] match. */
NRF_PPI...
Hi All,
Now I'm doing the OTA and I can use the nRF51822 DK and Master Control Pannel to complete the firmware update.I have a idear but I meet some problem.
I use the...
Hi,
Is it possible to update the firmware through usb? i have a nrf51822 evaluation kit, and i also tested the firmware update over ble. Now, i need to update the firmware...
HI Everybody,
I am developing firmware for handling multiple ANT+ Sensors. i am able to collect data from 3 different sensors, but in below scenario am getting channel...
