Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
Hi everyone, this is more of a programming advice question: basically we have a "registration app" associated with our BLE product which will be used to communicate user details...
Hello,
I've been developing code on nRF9160 for a while. In the beginning everything was straight forward and working just fine also the code was pretty simple. Now like...
I am currently working with the nRF5340 and using NAND flash for data storage. With the current code size, I need to create a secondary partition in the external NAND flash...
Hi,
I am using nRF52-DK to program a custom board based on BC832 (nRF52832 SoC). I recently updated "nRF Connect for Desktop" and associated applications. I believe some...
Hi there,
I'm trying to get the entire toolchain running on a new Win 11 AMD machine. Visual Studio Code has version 1.88.0, toolchain has v2.6.0 and SDK v2.6.0.
Therefore...
Hi,
i am working on Pancake motor C0820B006F circuit and it is connected to P0.12 pin and ground iam usin NRF52 development board. i want to change the pan cake vibrator...
Hello
We developped a firmware on the nrf52840 dongle able to communicate with a Windows PC through the USB.
On Windows 10, we can communicate with a serial COM port....
Hi, we looking at converting our devices from a BLE communication protocol, to BLE LR with MESH networking.
Currently, we are doing the following:
Android tablet connects...
Hi,
we are ramping up production, and need to make many production jigs, and programming in parrallell since the programming of the modem takes 1 min +.
We are using an...
