Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi, We're using the nrf9160 with ncs 2.7, modem FW 1.3.6 We're trying to send an HTTP request with TLS 1.2. We have provisioned our device and verified the key,cert with a...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
Hi,
I still have problems understanding the port and pin assignment for peripherals on the nrf54L15.
I need up to three SPIM, one UART and one TWI. That should work, right...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hi,
I'm working on an nRF5340 + nRF7002 project using Zephyr RTOS , where the device enters low-power sleep and wakes up on a hardware counter alarm ( counter_set_channel_alarm...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
board: nrf52832 DK
sdk: nrf connect sdk v2.6.1
I have successfully integrated the provisioner and light switch client together. Now I can control the light switch...
