Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello!
I am dealing with nrf52832. I want to process data reception with SPI during f_write processing. Is this possible? As multi-thread processing 1) PT_THREAD in pt...
I'm developing a wearable device using nRF52832. I am developing OTA-DFU nowadays. I have successfully tested the buttonless OTA-DFU using the nRF52-DK.
And I'm testing...
Hi, I have a nRF9160 and I am currently working with the gps example: ncs\nrf\samples\nrf9160\gps
When I run the example, I only see
all the time. I went out on a big...
Hello,
i am struggling with the implementation of i2s to use it one SK6812 Leds.
To start with i used this https://github.com/cheehieu/nrf52-sk6812-led-driver example...
Hi All,
I study this post to enable long-range(s=8) on ble_app_blinky ( nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_blinky )
In the post, one of the settings...
Hello,
I was able to program the mesh experimental dimming example(server) into the external nRF52832 module using the debug out pins on the nRF52 DK.
The programming...
Hi,, I'm trying to set a recv timeout on a UDP socket (coap) using setsockopt() and getting an EPERM error. I've tried the setsockopt() call both before and after the (successful...
I'm attempting to use AWS IoT Just In TIme Provisioning(JITP), but no luck. Any help.
I tested JITP on my account, not Nordic one, with local mosuqitto client on Mac and...
I'm trying to use aws_fota, but it doesn't work. Any help?
I was able to set a job on AWS IoT, but the download job doesn't start. The job status is always "in progress...
Hello
I am writing a peripheral emulator application on android. My peripherals include 2 services and 4 characteristics. I tested my application with nRF Connect on the...
Hello All,
I am working on nrf52810 board
Using sdk 14.2
I am trying to modify some bytes of advertising packet .
I am referring the previous post as link given...
I'm getting ERROR 12 upon calling ble_advertising_init. I understand that this is caused by exceeding the advertising packet max payload of 31 bytes. What options do I have...
Hi All,
I am testing the performance of a Relay Node in a mesh network.However it seems don't work.
I would like to show that the Relay node operation such as Rx and Re...
