Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I was trying to add generic onoff server model to the dimming server example in order to On/OFF and Dim the LED on the nRF52 Dev board using nRF Mesh App. I added all...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
I'm trying to integrate buttonless DFU in BLE app uart example. I added the file: ble_dfu.c, ble_dfu_bonded.c, ble_dfu_unbonded.c in the project. I added the following folder...
It's battery operation so I want to know how to setup 1sec timer and goto sleep_mode(power_down) after 1sec beacon scanning.
I'm using WDT to setup 60sec WDT reset so I...
Hi,
May I know what is the hardware layout for measuring external voltage using SAADC? I may not be understanding the infocenter or the datasheet for setting the external...
In the `Serial Interface`, the `Bluetooth Mesh Packet Send` command does allow specifying the `Time To Live` (TTL) for arbitrary packets, but there is no field for `Retransmit...
Hello, I have a question.
1. When ancs is reconnected, the machine will be reset, and the software will catch the log as follows.
As long as there are a large number of...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to know what would happen in the following situation.
During central and peripheral...
I noticed that in SDK SES projects, the linker file is generated every time the project is build. However, there is no memory map file specified, only a section placement...
I program in nrf52840 using thingy sdk
I succeeded in receiving the motion service.
The output speed of some motion services is too fast. such as raw, heading, gravity...
Greetings!
I'm new in the Nordic Dev Zone, so I apologize if this has been asked before. I just wasn't able to find a satisfying answer.
I read in this foruns that there...
dear
i am using this proj to get dfu functional
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main.c
i add some code in main.c...
