Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
Hi all,
I have a working ADC implementation (S130 + Application) and use it to measure an analog input continuously.
However if I use the same code on top of bootloader...
When I have a test using nRF24l01+ with STM32, I can only get a playload datarate no more than 450kbps using nRF24l01+ 2M mode.
How can increase the playload data rate and...
I have been using two NRF24L01 to communicate with each other using just simple Arduino Uno Board.
it worked for 5 days and now all of a sudden it is now working.
I tried...
Hi,
in order to add flash programming support to the iSYSTEM toolchain based on a
customer request I would need a flash reference driver/monitor implementation.
Would...
The sync time for my nrf2460 seems to be about 4 seconds. Is this normal? Secondly, once
the pair is synced at close distance, one or two feet, as I move away sync is lost...
I'm planning on having all of the different Device Information Service characteristics (fw_revision, sw_revision etc) with each being just a single integer for version number...
Can someone tell me what these errors actually mean
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -1.
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -102.
...
I am using nrf52840 central and nrf52840 peripheral device. Ble communication is enabled between and data transmission is working. I would like to analyse the packet loss...
Dear community,
I have your Thread example set up with 3 nRF52840 Preview Development Kit. nRF Thread Topology monitor 0.8.0-1 runs fine if I download CLI-example onto...
I use NRF52832 and sdk13.0.0 to develop my own application. I want to generate 1000 Hz Timer to trigger the ADC. I use the timer 1 to generate 1000 Hz. But when I use GPIOTE...
Hi,
In Nordic nRF51822, (please correct me if I am wrong), after I transmit 1 byte of data (since the transmit fifo is 1 byte long and receive fifo is 6 bytes long), I can...
