Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi. I have a problem, after upgrading the plugin nRF Connect for VS Code to a version higher than (2021.10.103) do not load modules of this plugin (photo attached). If I install...
Hello,
We are trying to setup the building environment for a nrf9160 device. We use the nrf Connect Desktop Toolchain for installing the environment and then we download...
Hi,
I want to connect to Google Cloud IoT with a modified asset_tracker and want the TLS done by the modem like in asset_tracker.
Google has a primary and a backup root...
Hi there!
After having worked with the nRF5 SDK and nRF SDK for Mesh, I'm off to a start for a project with LTE; CoAP to be precise. I'm using the nRF Connect SDK with Visual...
Hi,
I am working on a 2-wire uart to save GPIO and try to get as low current consumption as I can get.
Here is how I want it to be:
My custom 52840 board have 2-wire...
Hi,
I have created a custom board with a nrf52840 on it. I am working with Embedded Studio v5.64 and the Nordic SDK v. 17.1.0. When I use the preprocessor definition BOARD_PCA10056...
Hello Nordic experts,
Recently, I would like to implement high throughput with multi links. to optimize the system, I have the following doubts:
First of all, let...
I've recently put nRF Connect on my new machine, v1.7.0. I wanted to test the peripheral_uart sample application. However when I go to compile the peripheral_uart example...
Is it possible flash a nRF52833 over Bluetooth using the nRF52840 (PCA10059)? Or initiate DFU mode over Bluetooth using the dongle or a PC?
How could this be achieved?
In our application we want to connect to our server using LWM2M to exchange some data. To make a connection secure PSK key and indentity needs to be set to lwm2m objects:...
Hi,
I want to run my calibration code only once and this data store in flash (using FDS library) and not again even after restart. Is there any example of this kind of usage...
nRF52832, SD 132, RTOS, SDK13
Can anyone let me know how CPU will do when waiting for a message like below?
evt = osMessageGet(main_msgBox, osWaitForever); //wait...
Hi, I've got nRF Connect 3.6.1 installed on Windows 10. I just launched it, saw "Update" for all its individual apps and did so. Now most of them show an exclamation point...
