Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As software basis I use the “Zigbee cli example” from SDK V4.1.0.
So far, everything works...
I installed nRF Connect SDK v1.6.0 and SES Nordic Edition through the nRF Connect toolchain manager (Windows 10). I'm finding that I can't use the "open nRF Connect SDK Project...
Hello,
I'm trying to make the RF frequency of TX channel configurable.
I have noticed that anything higher than 0x50 is not acceptable for sd_ant_channel_radio_freq_set...
Hi,
I wanted to use the console on nRF52840DK in high-speed UART mode (921600bps) but it fails and I just saw the DK User Manual says:
Baud rate 921 600 is not supported...
I'm using the ble_nus_c NUS client code for a custom 1:1 data link between two embedded nodes, just pinging a few bytes of data back and forth every 3 seconds. Bonded connection...
Hi,
We are using nRF52840 SOC with our custom board . Due to some reason, the SWD data line( SWDIO pin ) shorted .
So now we are looking into how we can program nRF52840...
From SDK we can see that there is a lot of events about security. I've read some of them by comments and still a little confused about the difference of them.
Could anyone...
We're using the Azure iot hub implementation in a custom product that works with Azure.
One of the things we've noted is that if the total size of the device twin exceeds...
Hi,
I'm using nrf52840 in order to connect to a mobile and PC.
When connecting to a mobile, connection is bonded, but when connection to a PC, it's not, although m_sec_param...
We made the product by adopting BLE security mode 1, level 4. According to the analysis of our products by the wireless communication certification authority, We received...
I want to work on BLE. Pls suggest me a mobile phone I can purchase in amount of 25000 which supports:
BLE Long Range, Direction Finding, Advertising Extension, Periodic...
* Query on Combined DFU : 1. nrfutil version being used : 2.3.0 2. Followed nRFUtil for Generating DFU packages from -> https://infocenter.nordicsemi.com/index.jsp?topic=...
Hi! We're working on a testing Jig which should test our units in production.
One of the tests I'd like to make, is measure the current draw on TX at max (8dBm). I would...
Hello,
we are currently developing a new prototype board with the nRF52840-chip.
In order to figure out the best performance for our bt-antenna we decided to plan our...
i want to use orientation interrupt of bmi160. but i don't know how to read interrupt data. I wrote it after looking at the data sheet, but I want you to let me know if there...
