Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
I want to test zigbee functionality on nRF5340 DK board.
I have download nRF Connect SDK app and done the setup for its toolchain.
I have tried to find out zigbee examples...
Product specification does not list the maximum power level allowable at the RF input / output pin. What is the maximum allowable signal level at the RF input for the NRF5340...
Hi I have a question with nRF Connect SDK. I've already used nRF Connect SDK for a while and now I want to try with BLE and DFU on my PCA10040 board (nRF52832). When I look...
Hello, i would like to know what is actual heap and stack size because in segger memory usage i see that 8kB stack and 8 kB heap, but in my runtime memory view options i have...
Hello, can you please provide more information and instructions on how we configure the input capture on nrf52840 dev board using zephyr? All sample examples only cover pwm...
Hi,
Recently, we have ordered PCBAs using nrf52832 to online PCB manufacturers.
During a test, we found that some boards can use OTA firmware update, but some are not...
Respected Sir/Ma'am,
I have attached my schematic below.
I need to perform Offset calibration operation for which I need to control the SCLK value.
I am sending...
board : nRF9160DK
SDK : nrf connect SDK v1.5.0
sample : \v1.5.0\nrf\samples\nrf9160\lwm2m_client
Hi, i am testing lwm2m_client example and
Q1. i dont know how...
I'm trying to implement an immutable bootloader + MCUBoot + (SPM and APP), and then update the app via fota.
My implementation is based on the asset_tracker_v2 example....
Hi,
I'm working on an app where I need to collect data from a sensor, and send it over NUS every 10ms.
I'm using nRF5340-DK (0.11.0), and I'm using nRF Connect SDK v1...
Hi,
I need help to clarify the API for IAS zone server. If I can get example implementation, it would be great.
I have hard time understanding how zb_ias_zone_app_callback_t...
Hi,
I am new to nRF9160DK . I want to set RTC time for the nRF9160DK.
In the application we are getting UTC time from NTP server and we need to set RTC .
I have referred...
Hello,
I am trying to get my nRF9160 to connect to a https server via AT commands, but this is as far as I've been able to get.
In the end this will be used in a project...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
