Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi I am using NCS version 1.5.0 and DK version 1.0.0
If I want to build any application using nrf9160dk_nrf9160 Im getting the following error.
Traceback (most recent...
Hello, We are about to release a Firmware update for our vibration sensors and we are now testing the consumption of the new firmware. Our sensor is a nRF51822 + Accelerometer...
I'm building a BLE Peripheral device using Arduino and Adafruit's nRF8001 BLE module. I can find and connect to the BLE Peripheral using any number of iOS BLE discovery apps...
I'm using Windows 10 64 bit version. I've Nordic SDK example usbd_ble_uart_pca10056_s140 loaded onto my Embedded Studio. I compiled the code and loaded into the DK. I have...
Hello,
I try to add the pc-ble driver from Nordic to my Qt application, but my application crashes all the time without a specific error. So I need some help with the implementation...
I am running a GATT server on nRF52 and I am saving the CCCD state after bonding but does Android/iOS as a client also save the state? I only looked at the Android API side...
Hi,
I have two questions:
1) I'm making a custom board for a hobby project! Are there any limitations to running a SPI driver with a voltage high of 1.8V? It seems that...
So I am using ESB and want a very percise timer. Because the 16mhz clock is not 2^n we want it to roll over at a certain value that is a multiple of 16mhz, so we chose 4.096E9...
Hi, I would like to add LED animation when DFU is in place. I know where to start it and where to stop it in the secure_bootloader source. The main issue for me is to add...
hello,
i am using nrf52840 with coded phy in our customised board and using the long range example as base for my application i have changed the ble_app_blinky to act as...
I find that you have a NRF_CLI_USES_TASK_MANAGER_ENABLED Macro. But it uses your own task frame. our project want a example using FreeRTOS with complete CLI function, thanks...
I have recently updated from SDK 1.4.2 to 1.5.0 on an nRF5340-DK
I have an application with a custom ble service. Most of the services have authentication permission requirements...
Hi,
I use the app_buton module to handle the buttons. When detecting a button interrupt I call a function that sends data to I2S (using the "app_sched_event_put" function...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
I'm new to the nRF connect sdk (but have used the previous sdk in the past), and am wondering what the best way to start a new project is? With the old sdk, it was easiest...
