Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Is there a quick way to disable MCU Boot on the Thingy91 Asset Tracker example? I need to use the button on the device to my applicaton, and it is neccecary that the user...
Dear Sirs, good afternoon
I am using a (PPK + nrf52840 DK) to measure current on an external device.
Is it necessary to cut the SB40/41 jumpers in this case?
Thanks...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
Hello,
I got the acceleration value using mpu6050 sensor. And I am going to use this to get the angle of the sensor. The formula below has shown that angles can be obtained...
The application cannot write the app_update.bin on Windows.
How do I write with MCUboot & DFU & application?
[Command I tried]
dfu-util --alt 1 --download .\build_nrf52840dk_nrf52840...
Hi,
I have a similar issue as Wille in his question . I was trying to alter the example "nfc_text_record" for my needs. The code compiles without a problem, but when I try...
Hi,
After setting up my IDE and toolchain and trying out some example codes, I wanted to try the example for NFC pairing from SDK ver 17.0.2, because the pairing via NFC...
Hello,
I have some questions relate to Advertising:and RF ANT:
As I understand about advertising, there are only 3 channels, which can broadcast the advertising, are...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to follow this example.
I connected successfully, but I have problem in 'Advertising' part...
Hello, Support team:)
I wish to use NRF_LOG_DEBUG function in segger embedded studio.
But there is no message in "Debug Terminal".
- nRF SDK 16, "/examples/proprietary_rf...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
UART works normally at 3.3V.
But if I lower the power...
