Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
https://devzone.nordicsemi.com/f/nordic-q-a/67024/nrf9160-questions-related-to-immutable-mcuboot-application
From the above thread i learn that MCUBoot is not that...
To get the GPIO binding I can use:
device_get_binding("GPIO_0");
1. I would like to know where in the documentation it lists the strings you can pass to that function...
I am debugging the GPS function and referring to the sample code of the official GPS. As for the code of reading GPS data, I have a question that is the way of obtaining GPS...
Hi,
We are facing some issues between our ble devices (ble version 5) and android mobiles using nrfsdk ("Android-BLE-Library") library. (Version 2.2)
We are able to connect...
I have used two sample applications light / light_switch from bluetooth mesh to get a device with 2 elements:
- generic on/off clent
- generic on/off server
I want to...
Dear Sir,
The target has a non-secure bootloader on it, I'm trying for DFU which has a secure bootloader pkg only. After initiating the DFU, nrf connect app sends successfully...
Dear sir,
Thanks for your help.
In the working state, the input voltage of the battery may drop from 3.0V to 0.4v or even 0.0V. After charging, the voltage will quickly...
Hi,
I am using the Power Profiler Kit (Rev. 1.1.1.) with Power Profiler app (v2.3.1) to measure power consumption on an external DUT. The issue I am facing is negative current...
Hi all,
We have designed a PCB where we use BMD-350 ( which is based on nrf52832 ) , HX711 and the accelerometer ( MMA8452Q ) as primary components. The device is supposed...
I am in the process of integrating the latest SAADC driver into my project and have noticed an issue after adding the errata 122 workaround to my saadc event handler per the...
Thanks in advanced. On sdk17.0.2 examples\ble_central\ble_app_uart_c, I connect a button's one end to nrf52832 pin 24, the other end is connected to VDD. So I have to #define...
Hi,
There is an option CONFIG_LTE_NETWORK_TIMEOUT for the LTE Link Control. The default is 600 seconds (10 minutes) but I couldn't find any suggestions for the timeout and...
Hello ,
Now I am sending the data per 7.5ms in the interval of time over ble .I am loosing the packets , to avoid this I am planning to send the data in the structure .How...
Hi,
I got a unit based on NRF52 (No matter what SDK) which is connected via 1-wire (dallas protocol which is very time accurate) to other unit.
The other unit is the master...
