after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
Hi,
I've used the nRF51822 in the past to make sensors that connect to a mobile device. Basically it worked just like every other non-mesh BLE device:
1. It advertised...
Hi:
I'm developing a project with nRF 58232 in ble_app_hrs_rscs_relay example ( s132 sdk:nRF5SDK160098a08e2 ). The device need to be central and peripheral,My device worked...
Hi there,
I'm planning and hoping to use the nRF52840 (in module form) for an upcoming medical device design.
This will need to interface to a PC/Mac/Linux to send specific...
Is APP_TIMER_V2 supported by Mesh SDK 4.1? According to this forum, v2 should fix all sorts of issues related to v1. But it seems that app_timer_mesh.c is only partially compatible...
Hey,
I am working on a version which is uploaded from a bootloader (DFU), the bootloader print to UART and uses the UART libraries.
I want the application to close the...
Hey,
I am working on nRF51822, SDK12, S130, I wish to get more data into my advertising packet, however there is not enough space, I was thinking to COMPLETELY remove...
The goal is to be able to automate build using CMake. I am evaluating this by trying to build example project in nrfSDK 16.(I chose saadc example from nRF5_SDK\examples\peripheral...
