Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Dear all,
I have a problem.The DFU could not be performed due to a large size of the application around 300kB.
Platform : 52832;
SDK: SDK_11.0.0;
softdevice:s132.
If we edit the example code in seggar embedded, are the same changes done for the hex files of the same examples? IF not how do we change the code and put it in the dongle...
Hi,
I was following the instructions laid out in the "Configuring DFU over Mesh" guide in the nRF5 SDK for Mesh v3.1.0 ( https://infocenter.nordicsemi.com/topic/com.nordic...
Hello All,
I am working on nRF51822 custom board and i am not change it because it is customer requirement. Use IAR embedded workbanch IDE in windows 7. For reference...
This post mentions that only logical address 0 is supported for the coded PHY.
Is there any additional explanation for why this is? The OPS does not mention this.
...
Hello, I am working on a project based on a central/peripheral NUS application, with nRF51822 and SDK 12.3 .
I Want to know if the debit of data exchanging is lower when...
Hello,
I have configured the toolchain and SDK by following the NRF Connect getting started guide and followed the below steps to compile the mqtt_simple application (on...
Hi,
i m using central and peripheral code in SDK15.3 version,and i am not able to send or receive more than 20 bytes at a time in nRF52840 chipset.We are using Master...
Hi,
mbedtls is present inside zephyr/ext/lib/crypto but I cannot seem to build/link to it using Nordic's ecosystem. I haven't found a way using prj.conf to access it. Is...
This is my environment.
SDK: 15.2
IDE: Segger Embedded Studio
Platform: OSX
SoC: nRF52832
I am trying to transmit more than 8192 data using TWI.
But in fact...
I get the below linker error.
Error[Lt009]: Inconsistent wchar_t size nrf_cc310_bl_ecdsa_verify_secp256r1.c.obj(libnrf_cc310_bl_0.9.12.a) and 9 other objects in libnrf_cc310_bl_0...
Hello,
I am experimenting with the Flash Device Storage (FDS) API. Specifically, I'm using the nfc_writable_ndef_msg project as a starting point. It's a really good example...
Hi,
I am using nRF51822 dongle beacon and i have two dongles. iam flashing the code ,beacon transmitter(C:\sdk_12.1.0\examples\ble_peripheral\ble_app_beacon\pca10028\s130...
hello guys!
i using the 2 examples of light switch client and server and the mesh app for android all work fine, but i have some questions about those examples:
1. if...
Hi,
I am using Keil microVision5 with an nRF51-DK S130 and SDK 12. I followed the custom service tutorials in the link:
https://devzone.nordicsemi.com/tutorials/b/bluetooth...
