Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I would like to connect nearly 20 heart rate bands to the nrf52832 which has to configured as the central board and has to collect all the heart rate data from the peripherals...
Hi, I have a problem with my custom PCB.
Im ussing Segger in Mac, the latest sdk (15.02) and the latest softdevice too.
I have a custom pcb with a buzzer and when...
hello,
I faced interesting problem which I fortunately solved and would like to share with others because I hadn't found any information on this.
I am using nRF51822 on...
Hello,
we are currently trying to create sensor networks with the nRF52840 Dongle . Our first RSSI measurements in the field show that the orientation (rotation) of the...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant "examples\peripheral\pwm_library" to "examples...
Hi,
We have a firmware application using SDK 12.3 and Softdevice S132 V3.0.0 running on a nRF52 controller.The firmware is used pheriperial BLE device and provides a GATT...
I am working on ble_app_hids_keyboard example code. I downloaded the bin file in my eval kit and tried to connect the Nordic_keyboard device with my android device. Then,...
Looking at the "Pin assignments" section in nRF52840, I found that some GPIO pins are recommended for standard drive, low frequency I/O only. I am wondering whether there...
-SDK: 15.0
-S132
-nRF52832
-Segger studio
I'm trying to implement bonding/whitelisting to my project, which is a connectable beacon with a custom service. What I want...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant " examples\peripheral\pwm_library " to " examples...
I need to change, on a time basis, the advertising packet :
Let's say for X seconds it has to work as a "iBeacon"
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello,
We want to build Expiremental examples in BLE Peripheral.The Common issue which we have faced in bulding any of the Expiremental BLE Peripheral issue was the missing...
Hello. I am using the custom board (buttonless) of nRF 52840 to verify the services of DFU and NUS. After firmware rewriting with DFU, I confirmed that BLE communication with...
Hi,
Our Application software running in Micro is communicating with BLE over UART.
So in nutshell, we are using serialization to speak with soft device present on NRF52810...
