Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I'm very new to nRF BLe coding and I am having trouble finding what I need to proceed.
I have some PC Boards with inputs and I can connect to them through nRFConnect Bluetooth...
I have a BLE application running Mbed 9.7.2 on an nRF52832 (softdevice 132). I have a connection interval (to the central) of 11.25 ms and specify a slave latency of 3. I...
Hi! I've got a nRF52 dev kit and I'm programming it with SDK 15 with Keil. When I send 3 consecutive BLE notifications (each notification is 4 bytes) to the Android app, the...
Hi everyone,
right now I have two different kinds of Evaluation Kit: two FRDM-KW41Z from NXP with Thread Demo which can be found with this link:
https://www.nxp.com/products...
Hi all
Being fairly new to the nRF ecosystem I'm trying to get some basic code up and running on a custom board which uses a Rigado BMD-300. I'm using one of the examples...
Running into this with nRF Connect v2.6.1 for Windows
What happens is that the top-level app installs and runs fine, any apps that are added and launched within (or directly...
Hi,
I am working on the ble_app_uart which should forward data to the SPI port of the nRF52832.
It all works fine while the J-Link is connected. If I want to run my application...
I am playing the light switch example with nRF mesh app.
I am using nRF Mesh app read the light server state. and find out the app is really easy to hang when the device...
i am using this project,where can i download the origin app,soft,especially bootloader ?
the flash is been erased, i want the origin hex ,thank you
\nRF52832 pack\nRF5_SDK_14...
Hi,
Am using nrf52832 for my BLE project with SDK 15.02. I found sometimes device is not showing after disconnect, I have to reset the device manually to show the MAC...
I'm trying to update my project to use the latest S110 softdevice release. The trouble is that I have written many of my own hardware abstraction layers and they are conflicting...
Hello,
I am trying to program a nRF51 chip with a dev kit. When I install the base nRFGo Studio, it is able to detect the board but it won't read the chip because it is...
Hi,
I am experiencing an interesting case ( I am not sure if this is a problem indeed).
I have been trying to develop code for ISP1507 (nRF52832 PC10040 based) on two...
Hi ,
I have tried to test the current consumption on NRF52840-DK (PCA10056).
DCDC is enabled.
RTC is running.
No BLE is advertising.
The DK is powered via USB. ...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
