Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
Hello,
I'm using IAR 8.22.1, SDK 15.0.0, S132, nRF Connect V4.19.2.
I've loaded the 'secure_bootloader' example to PCA10040 EVB.
The device is recognized as DFUTARG...
Need to pass data from a battery powered sensor to a PC via a RF link. Would prefer
a COM Port emulation at 115,200 Baud. I already have a pair of nRF52 Development
Kits...
Hi guys,
Going through mesh packet format today and I'm stumbling upon the time_required_to_send_us method in broadcast.c which is used to calculate and indicate how long...
Hi,
I read and tried Mesh DFU given in " DFU quick start guide of nRF5 SDK for Mesh v2.0.1".
It says "To perform DFU transfers over mesh, use a customized version of...
Hi team,
Is there a way to figure out the phone id (to identify the source of pairing) after the phone has paired with the nordic device?
Basically what we need is is...
Hello,
I've downloaded nRF mesh and installed it on my iPhone, I can use it to provision my device, but there is a question about how to import AppKey on it.
I clicked...
I have a smartwatch, smartphone, and tablet.
I went to some place without any other bluetooth devices, my devices are able to scan and pair with each other. But nRF-51 not...
Hi,
I have followed sequence in http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fsdk_app_serial_dfu_bootloader.html&cp=4_0_0_4_3_4...
Hi,
I have a beacon code for nrf51 that I wanted to port to nrf52. It uses app_timer, gpiote and adc. The power consumption in idle is ~30uA. Now I wanted to port this code...
FDS_VIRTUAL_PAGE_SIZE
The size of a virtual flash page.
Expressed in number of 4-byte words. By default, a virtual page is the same size as a physical page....
