Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi!!
I'm adding spi functionality to S132 and SDK 14.0.0 ble_app_uart now.
The communication which added the function of UART to SPI and the sample code of ble_app_uart...
hello,
Now, i want to recover MAC from static random state.
for example, if MAC[5] =0X55 in chip itself, The MAC in adv in 0x1101 0101 ;
but i want mac in adv is 0x55...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I keep getting Mesh Error 6 while trying to combine the provisioner role with the client model. Which...
Hi,
I'm using nrf51822 with a custom board, where I should turn on a buzzer sometimes. I configure a timer and ppi to make a bip alarm. each bip lasts about 1sec; and the...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
hello! i have a problem ,when the Master send Slave SMP 37 Rcvd Pairing Request: Bonding, MITM, Initiator Key(s): LTK IRK CSRK , Responder Key(s): LTK IRK CSRK,but the slave...
Hello,
Thread Topology Monitor can associate an user name with a device. Where is it stored (in computer application or directly into the device) ? If it's in the device...
Hello All,
I am trying to interface an analog sensor with nrf52832, whose analog values have to be converted using SAADC and has to be sent over SPI to another chip. But...
I am testing the NR52832 using a BMD350 module on a custom made board.
Using the SPIM i faced the problem that i got an extra 500uA of current randomly. After trying to...
Dear Nordic,
We are using NRF52832 + RFX2411N for our product, and for lower the power consumption. we wonder if there has any way to know the CONNECT_REQ event.
In advertising...
After some time debugging an issue I had, I found out that my code was setting the I2C interrupt priority to 0, and at the same time that I'm running a Soft Device on my nrf52832...
Hi,
The Ch. 16 Power Supply Section of "nRF52840 Objective Product Specification v0.5" mentions the two power supply mode of nRF52840. This supply is available on the respective...
Hi.
I’m trying a multiperipheral function and have a problem.
The problem is I can not notify stable battery voltage with SAADC to the connected Central while advertising...
Hi, everyone,
We are developing BLE project on the nRF52832 chip (SDK 15.0) that must transmit to the big distances for about 20m. We set the transmission power to +4dBm...
Hi Dear nordic employee
I want to test the accuracy of my external LFCLK,
1、I enable the nordic RTC
2、set the prescaler 31（32768/32=1024），1/1024 second per step
...
