Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I am currently trying to work with pairing and bonding between the peripheral and Central device.
I am using two nrf52840 dk one as central and the other as peripheral...
Hi,
I cannot start HFXO on nRF52832. I'm using 32MHz crystal TSX-3225 32.0000MF20X-W0(from Mouser) wtih 12pF caps UMK105CG120JV-F(also from Mouser).
Checked with beeper...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
I am using this code to create and start transmission, but I cannot find a way to set the MACID to the internal NRF_FICR->DEVICEADDR values
My method with iBeacon is not...
I am currently working w/ a project that utilizes TrustedZone and PSA Protected Storage to read/write to internal flash that's accessible only in the secure partition (I'm...
Situation : custom nrf5340/nrf7002 board (very close to production...). Main image is overflowing available internal flash (with a MCUboot 64kB partition).
Secondary slots...
nRF52832 & nRF Connect SDK 2.6.1
We would like to reserve some internal flash for user configuration data that would be written in production like
and read by FW but...
Hi,
I am working with nrf5340 with the Zephyr OS. I created a custom data section in a custom linker file.
.my_data_section : { PROVIDE(__my_data_section_start = .); KEEP...
Hello,
I spent a solid two hours debugging an interrupt pin that was not working, to discover that the problem appears when configuring a callback in another part of the...
I have been bringing up an application on nRF54L15-DK, and about 50% of the time it hardfaults on initialization. I tracked down the cause to a branch to address 0, caused...
I am currently using DWM3000 EVK with NRF58240DK for a UWB indoor localization system. I want to use the timer to setup a localization period for each tag node. I tried several...
I am currently working on direction finding using the nRF Connect SDK in VS Code. I am using an nRF52811 custom board, and my logs work properly. I wanted to include timestamps...
Hello. I'm trying to control led in gpio pin in addition to LED pin in npm1300. I don't think you need to use resistance in LED pins, Is it the same when using led in gpio...
I am using NRF Connect SDK v2.5.2. Sometimes, after I factory reset my Zigbee router device, it will immediately join a network with PAN ID 000000000000. I get this with my...
I'm trying to move my nrf9151 project over to sysbuild (SDK v2.9.1) but when I try to use a custom board definition, the code fails to start up.
So far I've tried debugging...
