Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
To reduce power, I'm trying to find the best approach to minimize the cpu load when sampling an accelerometer at a high rate, e.g. 1.6Khz. Is there a way to DMA a sensors...
I am writing a crc checker for the application and the softdevice . I am using a s120 version 2.0.0 it currently has a upper boundary of 0x1D000 is this a hard boundary for...
Hi everyone.
I am making an application which combines two services (ANCS and Nordic UART). I compare the advertising_init() function from the two provided examples (ble_app_ancs_c...
Hi,
I've been searching the devzone for TWI examples, and preferably an example with MPU6050. Here are a conclusion of stuff that I found, but as some of them were for...
Hi ,
I tried to upload the application firmware using OTA service through MCP, I successfully get connected and the transferring of application hex file also gets successfully...
Hi Guys,
once again, I have strange behavior of my code.
In my code I try in loop after ble_event received change PWM from 0 to 255 for my motor device. In debug logs...
Dear,
Please, could help me ?
My knowledge in RF is basic.
I am developing a system to use 8 RF channels (nRF24L01 +) simultaneously.
I'm using Balum 2450BM14A0002...
Hi,
I’ve just ordered a few nrf51822 (from seedstudio ) and waiting for them to arrive.
They come preloaded with SoftDevice 6.0 or 7.0. with a pre-flashed OTA boot loader...
Hello, I am trying to connect a Nexus 6p running Android 6.0 to the NRF52 dev board. I have tried numerous ble examples in the SDK, but nothing ever appears in the nRF Master...
So if I start a program in debug mode some zero-inited static variables are non-zero.
ldr r1, =__etext
ldr r2, =__data_start__
ldr r3, =__data_end__
subs r3, r2...
I'm attempting to use the app_trace module. I've set it up as follows:
int main(void)
{
// Setup tracing. Also sets up UART.
app_trace_init();
app_trace_log(...
Hello,
I know that this question has been asked a few times, but I am a little desperate after trying to get debug logging over the Virtual COM Port to work. Here are the...
Hi,
I've recently got some brand new nRF51 Dongle, and used nRF51 DK. The problem is that DK is not recognized by mine PC. There's actually some example program (heart...
Is that bad to call RTT functions if there is no SEGGER connected?
I mean, if there is no RTT viewer connected, what the RTT library does with the message to transmit?...
