Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I would like to be able to use 3 different USB descriptors.
1. CDC ACM
2. Mass Storage
3. Composite device with CDC ACM and Mass Storage
These should be selectable...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK. I am using openthread protocol...
Step 5 of the Matter instructions at developer.nordicsemi.com/.../python_chip_controller_building.html
Shows getting the discriminator data. What is shown looks like the...
Dear Nordic Experts, A few short questions about mesh advertising in regard to Softdevice s132, 7.3.0, Mesh SDK 5.0.0 and nRF5 SDK 17.0.2:
How do you change the advertised...
Hello,
I'm running asset_tracker_v2 from v1.9.1 on a LTE-M network that does not give the time (UTC clock) info.
When no time information is given, the application should...
Hello
I have some questions about flash_fstorage example.
After reading the macro, it seems that fstorage will be located in .fs_data flash zone.
start_addr is set...
Hi,
Softdevice - 112
sdk 17.1.0
I am trying to evaluate the memory of the device. I am using nRF52810 and the datasheet says 192KB flash and 24KB of RAM available. ...
Hi I am using Unity test framework for generating unit test report and i also want to generate the code coverage report of the code for that i need how many lines of code...
Hey
I'm currently writing a thesis on IIoT and implementation in remote areas. We're trying to setup the nRF9160DK as EON device with all implementations on the board...
Hello,
I am experiencing trouble with NRF9160 chips that get stuck after typically 1 to 2 days of operation. This happens on all 6 boards that I have available. I'll describe...
Hi,
I am coming across an issue with app_scheduler and FDS.
While waiting for an event in FDS to complete (write, read, init, gc, etc) I go into a while loop calling app_sched_execute...
Hi,
What is the lifespan of nRF52810, operating at room temperature ? How long can it reliably work? Do you have some figures on this ? If yes, is it same for other nordic...
Hello everybody
I am using the nRF51 Dongle to connect via a third party app to a measuring device. This always worked very well on my first computer, the app could detect...
Hi,
I updated my Segger Embedded Studio for Arm from V 5.68 to V 6.20a.
Calling CMSIS Configuration Wizard fails with all examples with message : "Error starting process...
Hi All,
I have a nRF52840DK and looking for a solution to connect the VCOM serial port to the PC, without using USB. I will need to connect the serial port to another board...
