Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am trying to run the DNS example provided in the Nordic Infocenter as part of the Thread Border Router setup, but it is not working. I am getting "Error 28: ResponseTimeout...
Hello,
I tried to implement the HX711 example from Vidar mentioned here ( https://devzone.nordicsemi.com/f/nordic-q-a/34112/best-approach-to-interface-hx711-with-nordic...
Dear, I am developing first project for self training using Nordic MCU. I want to interface few Buttons, Leds and LCD. I read the Datasheet nRF5340_PS_v1.0.pdf. In it in the...
We have selected ble_app_hrs_pca10059_s140 file in peripheral and ble_app_hrs_c_pca10040_s132 in central device, Now we can able to send heart rate value to central board...
Hi
I can't find the information about nrf52832's blocker power level and harmonic in the nRF52832_PS_v1.4.pdf and infocenter,Could you provide the blocker power level and...
Hi all, actually I am able to flash ble cental code to development board, and can able to connect and send data trough nrf connect app.
But my issue is, when the power to...
Hey everyone,
im currently trying to print a message once a gpio interrupt is fired over usb to the serial console. Therefore i basicly merged the basic/button sample with...
Hello,
We want to update our environment to use Python 3.10 due to added features such as match cases. However, we use the nRF52840 dongle together with pc-ble-driver-py...
Hi -
Just received thingy 91 and updated the firmware, but accidentally out of order. Wondering how to recover from the error "no matching trait found" when trying to update...
I am working with UBLOX AOA part and trying to program a custom module of nrf52833 instead of their UBLOX C209.
According to UBLOX they are using NRF CONNECT SDK 1.5 in...
Hello,
Using an nRF52833dk and following this documentation https://github.com/makerdiary/nrf52840-mdk
I was able to flash the blinky example on my board, but only once...
Hi All,
SDK => v17.1.0
IDE => Segger
Project => Peripheral - libuarte
When I communicate with other development board, if I use this block of programs, nrf_queue_push...
Hi All,
I am trying to understand the possibility of using Bluetooth Mesh technology for voice communication for longer distances.
My main problem is to communicate longer...
Hi,
I was wondering if it was possible to notify the application layer if the central device is scanning and it (the central device) sends a scan request to an advertising...
Hi,
I have two questions regarding the UART and SPI communication at high speed.
I am using the UART and SPI to transfer data on nRF52832 and sdk 17.0. I connected an...
