after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
Hi .thank u for reading this .First sorry for my english. This is the story:
I try to make a flexible mesh using multi nrf24l01+ more than 10 nodes. I searched so many topic...
While running a Scan in nRFConnect 4.24.3 on Android 10, Nokia 6.2, I see the first Advertisement from my BLE Device. That device advertises different sets of ScanData over...
Hi ,
I am working on a project where i need to publish wifi scans over ble , issue is that when ever we try to send data over it either send or not sent to avoid data loss...
Does Nordic have some solution for this? Device would be a WiFi+BLE gateway, which runs Linux, and can support advertising scan for at least 300 beacons, and have Ethernet...
Hi, I am running into issues where the nRF9160 (in NB-IoT mode) does not seem to handle cell changes reliably. I am using modem firmware mfw_nrf9160_1.2.0 . I made a simplified...
Hi Nordic guys,
I'm trying to create a pin pairing between an NRF52 DK and iPhone.
I've created this function to do that:
I've added that function in the ble_peripherical...
Hey! I am using nRF52 DK, SDK 15.2.0, and softdevice s112. I have an application that reads some data with the saadc, advertises, sends data if a connection is made or stores...
Hello
I am facing problem from many days on buttonless DFU.
Whoever from Nordic approaches kindly give a customized solution rather than other links. I have almost gone...
I am developing a BLE to LORA interface using nRF52840.
The LORA transceiver needs a 32MHz clock. Is there any way that I can get the nRF52840 to generate this?
I will...
