Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I used my app based on the ble_peripheral_gls example in sdk 14.2.0.. and I applied static passkey, "000000" to our app.
When I tested my app with android phone runinng...
Hi,
I find the smallest connection interval I can set on 52840 (and 832 as peer) is 8 units (10ms), and I am not sure if that is reasonable.
My configuration:
52832...
I have a question concerning this tutorial : devzone.nordicsemi.com/.../ble-characteristics-a-beginners-tutorial
i have same problem than Milton (comment under the tutorial...
We have procured nRF52-DK development board from Mouser India and we are using S140 stack on the Windows platform for our PoC.
Our application requires that nRF52840 should...
Hello,
I would like to modify the current default SRAM partition from 64k (secure), 64k (bsd), 128k (non-secure). I would like to change it as follows; 8 k (secure), 8k...
See: https://devzone.nordicsemi.com/f/nordic-q-a/46833/nrf-connect-can-t-see-nrf52-dk/185284#185284
I have been developing a peripheral with nRF52832 and SDK 15.3.0.
I...
I'm stuck over fds_init() which hangs on mbed-os using SDK 14.2
I am calling fds_init within bleInitComplete callback as follows:
BLE & ble = BLE::Instance ();
ble...
Hello,
The pwm example shows changing the duty cycle inside the main while loop with delay wait.
I would like to get rid of this delay wait by putting the app_pwm_channel_duty_set...
Hi, may I know whether there is a way for nRF52832 chip to directly have access to the variable gain amplifier (VGA) inside the chip? Namely, our input signals goes directly...
Hi,
I am using the sdk 14, S132, ble_app_uart example.
My nordic chip receives data from the MCU over UART and passes out to mobile application over BLE.
using the nrf...
hi i am trying to integrate nrf_butoonless_dfu service in ble_app_uart code in nRF sdk 15.3.0,
i have added the all the required source files and include files and macro...
I am attempting to implement an application using the s140 6.1.0 softdevice on an nRF52840 which "concurrently" advertises as a connectable device while at the same time transmits...
I try to solder a EBYTE NRF52840 module by my PCB and connect with SEGGER programmer. I try to connect to 4 wire VDD, GND, SWDIO, SWCLK, like the one that I have with NRF52832...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0. I use gcc. I just got it to link and flash and I'm seeing RTT logging OK, to a point. I also have the flashlog in use...
