Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
I am working on NRF52840 DK for a project on Bluetooth Mesh. Using Segger Embedded Studio for Building and debugging.
Basically i am trying to run the examplecode...
I'm writing two 32 bit words. I've verified that the source and destination addresses are word aligned (the UICR address is 0x10001088 and the source address is 2000200C)...
hi.....
i have merged the two programs ble_uart and twi sensor ......in nrf52832 ...segger15.2
i have attached all c files and h files ...... no errors ...when flashing...
Application on NRF52DK running fine average current 2uA. After installing hard and software for the PPK power profiling kit the application draws 8 mA!
Application functions...
Hi guys,
I have a board with STM32 (mbed os) and NRF52832 connected using UART lines.
STM32 has a internet connection and NRF52832 has a bootloader and DFU service.
...
I want to send sensor data from one node to other using access_model_reliable_publish() method, but my data is too large and I'm not able to send large data. What is the maximum...
Hello,
I'm using the TWI example mentioned in the subject line and I'm trying to get the TWI signals out of my demo board (Rigado BMD-350 Evaluation board).
Am I right...
hi everyone
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
And I`m using ubuntu via Virtual Box
I refer 'pc-ble-driver' and follow...
Hello.
I am trying to build something like this in the picture below:
so my guess is that I need mesh functionality.
So my initial questions are.
Are there any...
Hi Sir
I start development form uart cli example (uart0), now nrf52840 module will connect an uart peripheral device by uart1, so two uarts would be used.
My goal is to...
Hi all,
I try to develop a gamepad using 51822 by modifying the keyboard example code.The button works well after PC connecting the device the first time ,but when I power...
Hello everyone,
We are building a wearable that uses nrf51822 chip. We are facing a specific issue of connection and disconnection every 30 seconds with Android devices...
hi...
i am using nrf52832 and sensor ......... is it possible to read the data by interrupting the sensor
for example ....
if i am using temperature sensor if the value...
