Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Segger provides great information for the use of the JTrace for tracing and profiling with the NRF52 development kit here.
https://wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52832...
Hi,
I'm expecting using a custom board with nrf52832 running connectivity program as a host to connect to the perpheral, and the hrc v5 example of pc-ble-driver is used...
hello support team
I am trying SDK Proximity coexistence example
I am using Mesh SDK 2.2
and nRF5_SDK_15.0.0_a53641a
I followed the steps given in link
I am getting...
Hi All,
i am working on SDK-14.2, i am facing issue with ble disconnection in dfu mode.
by using nrf-Connect in mobile i am upgrading the firmware, but it lost connection...
Details:
nRF52832
SDK 14.1 with matching SD
Compiling with GCC
I am trying to solve the following problem:
My device is powered by a coin cell (Manganese dioxide...
Hi, when my program calls sleep_mode_enter(), it enters system off (deep sleep) as expected. However, when I press the button on the Thingy52 to wake up, the bootloader starts...
I have problems connecting to a NRF51802 via stlinkv2 and openocd. I also tried a black magic probe flashed onto the blue pill board. Both did not work. I have ordered a NRF51822...
SDK 15.2
The nrfx_uarte_event_t callback contains a nrfx_uarte_xfer_evt_t; structure,
this structure has the bytes field as a uint8_t this should be a uint16_t to support...
Hi,
I'm using nrf52dk and SDK v15.
In my application, I have 2 input pin and I want to disable one of them when in one of the 2 pins occurs the event low to high, is it...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
Greetings,
I'm having the same weird issue as this question, though I don't understand the answer to it https://devzone.nordicsemi.com/f/nordic-q-a/34447/app-gets-stuck...
Hi everyone,
I've a nRF52810 based device that I am working with the Android based nRF Connect app on a Poco F1 (Oreo 8.1.0). The app scans the device properly but connection...
I just got my new nRF52840 dongle and went through the procedures stated. But I tried programming the nrf blinky firmware and after that I'm not able to connect the dongle...
