I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
uint32_t ble_advdata_set (const ble_advdata_t *p_advdata, const ble_advdata_t *p_srdata)
If I set the second parameter p_srdata, does it mean passing encoded advertising...
Hi I want to ask about the best way to handle a lot of incoming bytes via UART on the nRF52832 (SDK 15.0.0). Unfortunately, the parsing of incoming data seems to be slower...
We are moving from using the Device Manager to the Peer Manager.
We are concerned about side effects concerning updating customer device firmware. One issue of concern is...
I stumbled upon Nordics video on facebook where they show how to calculate the distance between two NRF52840 Dev Kits. Link to video and article: devzone.nordicsemi.com/....
I downloaded version 15.2.0 of the nRF SDK. It contains the softdevice version 6.1.0.
I then attempted to upgrade to the softdevice to 6.1.1. After downloading the softdevice...
Hello,
What are the steps to recover a bricked nRF9160-DK? I want to get it back to the state that it was shipped in. I would assume refresh "secure_boot" and an app such...
Sir,
I have one custom MDBT50Q evaluation board and a ST-Link debugger. As the Keil IDE is fully defaulted to J-Link none of the example programs are building and flashing...
Hardware:Two nrf52840 DK Software: SDK15.2
We have 2 development boards acting as a master and slave communicating over UART. We are using the serial library for this application...
when i use the official example in nRF5_SDK_15.2.0_9412b96\examples\peripheral\blinky\pca10040e\mbr\iar using IAR IDE,
after building successfully, i failed to download...
Hi:
I use the new Mesh SDK 2.2.0 to make a demo.and I use the proxy_server and proxy_client example. now，I test and find the proxy_server example don't open the relay function...
Hi,
When I go through the code of light switch example, I am confused about relay functionality.
Compare with the v2.1.1, I can find the m_relay_enable in network.c but...
Hello!
We are currently developing a software solution which integrates many protocols into one Gateway. One of the protocols is Zigbee, and since it is the first time we...
I'm running FreeRTOS with SDK version 15.0 on nrf52 custom board.
I have two sensors, say A and B, on two separate SPIM bus instances. Sensor B utilizes PPI to trigger data...
I've been working on using an nRF52 as a host for a PS/2 synaptics touchpad mouse (to integrate with BLE HID). I was able to get a correct mouse position using two GPIO pins...
Hi,
i am using oled ssd1306 i2c with nrf51822. I am using peripheral mode and SDK v10.0. i choose this sdk version because of length i want to sent at one go that is 1024...
Help pls, i can't build a project.
Building ‘temp1’ from solution ‘temp1’ in configuration ‘Debug’ 1> Generating linker script ‘temp1.ld’ 1> Linking temp1.elf 1> Output...
