after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Everyone,
I have successfully configured RTOS and BLE alog with onboard LEDs blinking into an RTOS code.
Everyhting runs fine if i run only the 4 tasks of LED blinking...
Hello!
I need to send 20 x 20 bytes with the nRF8001 and would like to reduce the transmitting time as much as possible to set the MCU and nRF8001 in sleep mode as long...
Hi,
I am confused about the ROM layout, would you please correct me? Thanks.
Based on my understanding, for open bootloader scenario(like nrf52840 dongle), the bootloader...
I am using the nRF52832 with the S132 soft device. I am trying to send a large amount of data (~5 kB) from a phone to my BLE peripheral. I am wondering if the queued write...
I Have attached my project which is an SDK 15. project, starting with the simple twi sensor project and including some functions calls from gpio from SDK 14.0, porting gpio...
Hi,
The following is the guide under this ticket: devzone.nordicsemi.com/.../where-i-can-find-the-example-of-usbd-dfu-for-pc-side
Terje said "you can use nrfjprog with...
Hello everyone
The following warnings and errors occurred
Warning[Pe223]: function "sd_flash_write" declared implicitly D:\ZIP\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hi I am developing on Adafruit LE UART Friend ( https://www.adafruit.com/product/2479 ) platform. Compiler: GCC 7.2.1 IDE: NetBeans NRF SDK: 12.3, SoftDevice S130 Debugger...
Hi,
I am trying to interface ESP8266 WiFi Module: https://www.amazon.in/OLatus-ESP8266-Wireless-Transceiver-Raspberry/dp/B072BG8LW1/ref=sr_1_1_sspa?ie=UTF8&qid=1531738374&sr...
Hello-
I am working with the nRF52840 with the 14.1 SDK.
I am using the 15.4 UART example and currently only data_ack is enabled. I am hoping to add poll_data and poll_ack...
I would like further clarification on nRF52840 Errata 179: RTC: COMPARE event is generated twice from a single RTC compare match.
I am creating a sensor system that needs...
Hello,
We designed an antenna for our new product and we would like to have your feedback on it before making the prototypes. Below is the design
The dxf file...
