after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I used to program my PCBs using the nrf52840 PDK, however, my mac no longer recognized the PDK. The PDK turns on and the application runs as LED 4 blinks but the LEDs next...
hi,
i am using ble_uart example to take time when data arrives and time when data being sent over bluetooth.
when i prints the time without connecting to bluetooth. then...
Board:custom board
Mesh SDK: V1.0.0
IDE:SEGGER Embedded
Problem a：
When I test the steps specified by “Interactive PyACI”, there is A certain probability of Provisioning...
Hello,
i asked this quastion once in this thread: https://devzone.nordicsemi.com/f/nordic-q-a/32444/reset-on_ble_connect-when-button-event I accepted the given answer but...
Hi Nordic Team, I'm trying to setup a gcc/eclipse based environment according to gustavovelascoh.wordpress.com/.../ on Linux/Ubuntu 16.04.1 64Bit. The Ubuntu system lives...
Hi, I would like to make an exact copy of the nRF51 dongle antenna (as was recommended by multiple blog posts by Nordic). I am concerned about the legal issues, and any IP...
I search GPIO pin bit definations and register. I saw pca10040.h GPIO defined.I dont know how to configurated P1DIR, P1EN, P1OUT etc.. I studied Texas Instrument before. I...
Hi,
I'm making my own prototype board using the nRF51822. this board is powered by a rechargeable battery lir2450 (3.6V): www.powerstream.com/.../Lir2450.pdf
i want...
Hello world
after several hours & day, Finally I have to implement this KNN code and nRF51822_adxl345 code. I have implement to one. but there is problem that..
I can...
I am trying to track down a fatal error and want to use the Error module as documented below, to get the line number and file name.
Using eclipse, where should DEBUG be...
Hi,
My customer issue problem on his redmi note4 of mobile.
Step1: The customer used mobile to bond the peripheral of nRF52. And then the nRF52 device add the bond of...
hi,
i am working on generic ble central device which has nrf52832 as it's core.
my question is that i want to know the length of data in bytes which are being sent by...
Dear Nordic,
I have located the Serialization example project (using SPI) for the Connectivity board, but I cannot find an example project for the Application CPU board...
Hi,
I have two WT51822-S4AT boards. My goal is to have this setup:
PC <--> board 1 via UART <--> board 2 via BLE <--> MCU via UART
I have flashed one of the boards...
