Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI al
I have a bicycle computer (A) host (SDK 12.1 51822QFAC S130-V2.0.1) and a slave device (B) for measuring bike speed and cadence (using 2032 batteries). 1. When the...
Hi, I was recently asking about OPUS - https://devzone.nordicsemi.com/f/nordic-q-a/32875/how-compile-opus/128181#128181 . Now I am able to run encode on audio data and decode...
Hi
We have a nrf51 dongle for use in a school prosject When the nrf51 dongle is connected to the USB slot in a computer it boots fine without holding the button when powering...
On the Getting Started page, I do not see the USB described in Step 7. I do not see any device. The LEDs flash and the buttons light up LEDs 1-4 as described.
Thanks
Hi,
I'm using nrf_serial 'object' in order to communicate nRF52832 with an external device.
As I work in non-blocking mode I need to verify if there's available space...
Hi,
We are migrating SoftDevice 5.0 -> 6.0.0-6 alpha on sdk 14.2 (s132->s140) in order to be able to evaluate long range. During the migration we stumbled across some problems...
hi all,
I have an issue with hardware in the circuit, which is designed by my self. The PCB has designed a customized
condition:
I have erased full memory and measure...
we want to support the serial bootloader with SDK13, but find that the example is Experimental: Serial Secure DFU Bootloader, can we use it stably? the SDK14/15 don't Experimental...
I am using nrf52832_xxaa and SDK11.
Is there any formula that states the relation between the advertising & scanning parameters(advertising interval, scanning interval,...
I am trying to flash the program into my custom board. and i am successfully flash the program into custom board. I have flashed the blinky code in y custom board. it's works...
Hi everyone,
I would like to know in the ble_app_uart_pca10040 where the Bluetooth antenna is connected on pin planner to be able to change it.
Thanks you for helping...
Hello there,
I have a question related to the ADC of the nRF52832.
I am using it in single-ended mode, 10-bit resolution, 1/5 gain, internal reference 0.6V.
Thus...
Hello,
I am wondering what this "Low Power Event" is.
I am looking through the document but I can't find the place that explains this.
Can somebody point me to the place...
Hi, I followed the tutorial to Debug with Real Time Terminal on Keil.
fatal error: file sdk_config.h not found.
I have followed the tutorial as precisely as I can, maybe...
hi，there
I met an error in Nordic_HRM examples. The error code is GATT_CONN_TERMINATE_LOCAL_HOST.After the connection is established, you can see the service that has...
