Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
Some little compilation errors.
in ble_radio_notification.h
typedef uint8_t nrf_radio_notification_distance_t; => is no more defined in SDK but used here
...
I need to do an hybrid app like nRF UART App but with cordova. i can connect and disconnect, but i don't know how to catch the data every time the ble send.
i'm using this...
Dear all,
I make a simple test on the UART0, putting the code in 'simple_uart.c' to my main.c. When I send out a character 'A', 0x41. From the CRO timing, it appears that...
Hi all,
I am developing ble mesh network, the source code taken from this link: github.com/.../nRF51-ble-bcast-mesh . First i tested led mesh example for two boards.
...
Hi, I need to use whitelist in ble_app_uart example, What are the steps that need to be followed for that. Is device Manager is mandatory for using whitelist. Can anyone throw...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
Hi Nordic Community and Developers,
I'm designing a small Bluetooth module using nRF51822 to use it in my next projects and I need to use thinner substrate material (~0...
I have an application that we have ported to the nRF52 that used an EEPROM to manage configuration values. This application doesn't update these values often but when they...
Hi All, we have used Arduino modules based at 24L01+ in our application, now we are getting to apoint where we need to find one of theese or another one and do a redesign...
Hi, I'm searching platform for my project.
I will need to send packets from big quantity of transmitters (nRF24LE1) to one reciever (nRF24L01), it will something like voting...
Hi i am interfacing mma842with nrf51822. but i am not getting data. i have uploaded code. can you tell me what is problem. i don't know i am not getting who am i id try.r...
I've noticed that our custom board sometimes does not work (e.g. execute the code) when the VCC drops to about 0.3V- 0.5V and comes back on again to 3.3V.
For testing I...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
In SDK_v11.0.0-2.alpha, there is a project: examples\ble_peripheral\ble_app_hrs_freertos\pca10028\ble_app_hrs_freertos\s130_with_dfu_pca10028.
But I can't find DFU service...
to # einar thorsrud
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive...
