after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
When I use "sd_ble_opt_set" to set channel map as below, the API will retrun...
Brand new PC running windows 10.
Installed all of the necessary drivers (J-Link 5.12f)
To clarify any tool that tries J-Link connect crashes.
Also same behaviour with...
Im having problems running DFU serial examples.
i use one of the examples of the SDK but it seems like board doesnt leave the bootloader mode and memory value doesnt change...
Does someone could tell me where can I find information on the sequencing of events BLE_EVT_TX_COMPLETE and packet transmissions during connection periods?
In my application...
Hi,
I am using nrf51822 evaluation kit, and the sample program i am working on is ble_app_hrs.
I have created 4 characteristics with notify property and also created...
Hi every one,
I'm working on a custom broad and I'm trying to setup a gazell based protocol.
I had a solution using soft device and BLE which worked fine but we want to...
Hello,
I'm a few novice in BLE, and I've got a problem.
I'm using a custom project based in UART example. I'm using Nexus 5 and nRF ToolsBox for text it. I'm saving...
Hi! I want to send the temperature data that I get from the beacon sensor not one by one but in packets for example of 100 samples. I have followed this tutorial devzone.nordicsemi...
Hello,
I am trying to get SPIS EasyDMA to work. Currently the SPIS MISO response with high when the CS is pulled low by another master device, but no correct data present...
I'm trying to add more buttons to the nRF51 DK.
But I get an error.
I have found the NUMBER_OF_GPIO_TE define.
#define NUMBER_OF_GPIO_TE 4
How can I handle more...
Hi, is there RSA-512 cryptography (or maybe another asymmetric cryptography system) implementation for nrf51 or some implementation that can be easily ported to nrf51?
Hi. I played around with the MQTT example on nrf51822 module.
I get it connected to an openwrt device and can connect/publish to mosquitto on button press.
In next step...
Hello all
If you could please point me some directions on how to solve my issue, I would be grateful:
Some background info:
SDK used: 9.0
spi master code =...
Dear Nordic Developer Zone,
I have a silly question. After searching in the Nordic and Bluetooth documentation, I didn't find what CCCD and SCCD mean. Theses metadata are...
I had a design on 4-layer PCB with nrf51822, then the requirement was changed, then the 2-layer is sufficient for routing.
But I thought 4-layer PCB is better for RF circuit...
