Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi!
(My apologies in advance in case the information I need is to be found elsewhere. There are numerous tickets related to GPS/A-GPS, but everybody seems to have his/her...
Hi,
I keep looking at different posts and I struggle to understand.
Is it possible to save to flash (nvm) on a nRF51422 with s130 while the Bluetooth is ON and connected...
Is there an easier way to print out debugging statement that does not need an installation of a logging package in keil.
I am trying to place print statements within the...
Hi,
I'm trying to create a Node application (using Noble) that acts as a DFU controller so that I can automate DFU'ing hundreds of devices (nRF52 using SDK 15.0.0). I've...
Hello, I want to use the Nordic Thingy:52 products to extend the Bluetooth range from my phone to a Nordic Development board. How should I start? Any suggestions? Thanks!
Hello
I am using nRF5 SDK ver.16 to try to create a BLE HID touchscreen device. I referenced ble_hids_mouse example and changed HID report map. On Windows 10, it works pretty...
Hi,
I am getting started with nRF9160DK so that I am try to build the application nrf_cloud_agps on segger embedded studio. But I cannot build the application, it says that...
Hello All,
I am working on nrf52810 chipset and using SDK 17 for my development, I have modified BLE_HTS code by adding peripherals like I2C and ADC, I can able compile...
Hi, I am trying to use the BLE Direction Finding on the nRF52833 dK.
1. Are there any software examples I can use to help me get the direction finding running?
2. Also...
Hello,
I have created an application that collects data from sensors and GPS in two separate threads and publishes via MQTT. The two thread priorities are set to 10 and...
MIN and MAX macros are commonly defined in many code bases. These macros are also defined in nordic_common.h. To avoid conflicts with other libraries, it would be great if...
Hi, I have two pins, one handles a system wake-up event and the other reacts to an external uvlo event. The wake-up event is the only PIN that can interrupt and it configures...
Hello,
when I send notifications or indications to central device without bonding it works perfect. But after bonding they are not sent. I receive following logs when cetnral...
I am using nRF52840 dongle and nRF SDK version nRF5_SDK_17.0.0_9d13099.
When I am trying to debug the application it gives an error.
using your example project on nRF52840...
