after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am using nRF52840 dongle and nRF SDK version nRF5_SDK_17.0.0_9d13099.
When I am trying to debug the application it gives an error.
using your example project on nRF52840...
I can't go into too many details, but the scenario we have is:
We have an NRF52840 device connected to a PC through serial (for both power and communication) The NRF device...
I am trying to create a minimum working Keil uVision 5 S132 project with PCA100400. When I compare the examples with mine, I notice that during startup, when the code of flashed...
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
Hello,
We have a product that sends out an ESB message approximately ever second, it does this using the RTC timer with the following setting:
It sends the message...
We want to add the nRF52805 to an existing product but also want to have the option to perform a firmware update.
The current DFU implementation doesn't allow the softdevice...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
Hello,
The Power Profiler Kit(PPK) is not able to measure current consumption. I got this notification asking to reprogrammed the device, I clicked yes and then-after it...
