Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I'm trying to understand why this happens.
My application uses the softdevice, which configures some NRFFW registers. I program my application, bootloader, SoftDevice via...
Hi
I am using nRF connect for nRF5340 and i am in need to compile using segger embedded studio.
I tried installing segger IDE with the version 4.5 , I got the free license...
Hi,
I encounter a issue with my printed broad that mainly copy the thingy52. I download the thingyv210HW10.hex into my hardware. And then I debug the code (thingysdkv210...
Hello,
Currently, we are working on a product which leverages the following:
NRF52832 (64KB RAM and 512 KB Flash)
SDK v11.0.0
Soft Device 132
It has been reported...
Hi,
I see from the code in GitHub:
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/supl_support.c
That the new A-GPS is using...
Hi! I'm performing buttonless Secure OTA DFU operation on some custom boards of mine. I'm using nRF Connect v3.3.1, and at the moment I'm flashing a zip file containing my...
We have a door lock product. At first, the capacitance value of bluetooth frequency deviation was not adjusted, and then it was very difficult for apple to connect with vivo...
Hi,
I have a problem that can not receive FDS_EVT_WRITE event, but fds_record_write return NRF_SUCCESS when using FDS and FreeRTOS simultaneously on nRF52840. And FDS_EVT_INIT...
Hi,
In the ble_app_uart example I am trying to read a binary file and send it to the application using nRF52840 board. I have send 32 packets of data periodically.If a delay...
Hi. I am looking for a reference FW design for BTLE where I can define a custom Service and Characteristic where I can send arbitrary (minimal length) data from peripheral...
Hi,
In our application, LCD will occupy 150KB RAM, and algorithm will occupy 60KB, but 52840 only has 256KB ram, so 256KB RAM is not enough for our application;
We want...
To realize multi touch in hid, we need to realize get report request to get the maximum number of support points and set report request to set touch mode. In the SDK 15.3...
Hello,
I'm trying to add a third characteristic to my BLE service and when I add it, my device "fatally" crashes in Release mode with no meaningful error information ...
Hi I'm having trouble updating the firmware on a custom board using JTAG through the NRF9160 DK.
I've attached the log file from the programmer of the error I'm getting...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
