Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
How do you recommend to analyze nrf52840 dongle power consumption?
What I have is:
Nrf52840 dongle
Nrf52DK
Nrf6707 profiler kit
How can these be used together...
I am looking for a .hex file application for the nrf52840 dk that I can control from an external application via the USB port in order to setup and test the physical layer...
HI, Im developing a custom board (NRF58232) with a bmx055 connected by TWI.
I have used the twi_scanner and twi_sensor and all OK, It was working !
But now I want to use...
From what I can tell, the SDK for Thread provided from Nordic uses a precompiled Openthread library that hardcodes the UART pin configuration. This means that users of this...
I'm developing on the nRF52840, SDK15, and s140 v6.0. I'm trying to use the sd_power_gpregret_set() function to write a value that would then be read after reset to start...
Hi - I'm using a nRF52840 DK for the first time with my 2010 MacBook pro running OSX Sierra version 10.12.6. I have SEGGER Embedded Studio for ARM 4.12 installed and Segger...
I've been trying to get TWI Sensor to work on 3rd party boards for a while now and no luck.
The code I'm using is only slightly modified, (1) it explicitly defines .scl...
Hi,
I am using ppk with nrf52832 dk to measure the current consumption of my board and it giving different values at different times. for two days it gave 250uA and tested...
Please tell me how to modify the base UUID of the NUS sample application (app_uart / app_uart_c).
SoC: nRF52832 SDK: nRF5_SDK_14.0.0
<My background> I am developing BLE...
Hi Guys,
I'm interested to get guideline on how could I customized the qspi example from nordic in terms of pins and command. I don't see any different between MX25R6435F...
The NRF_MODULE_ENABLED macro does not play well with Eclipse. I've tried enabling all Modules in the Symbols section of Eclipse but still it does not enable any module utlizing...
Hello all,
Anybody knows "EVENT_STARTED does not fire" issue will be fix or not?
I really do want to use the PPI function at Tacq=3us.
When can I get the counter measure...
Hi,
I am trying to use EasyDMA. Is it preferable to use with ...\peripheral\uart or ... \peripheral\serial. With ...\peripheral\uart there are lot of errors. I tried with...
In the code above I get an error that nrdx_gpiote_in_init() and nrfx_gpiote_in_event_enable() are undefined.
In CMSIS configuration wizard -> nRF_Drivers i've enabled...
