Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi guys,
I'm using following setup NRF51822, SD130, SDK 12.3.0. I control one transistor with PWM output via timer 1. Before enabling PWM I start 8bit ADC task to measure...
Does the Nordic UART Service (NUS) have a facility to confirm when a sent message has been received by the peer?
In particular, to confirm when an NUS message sent by a...
Good afternoon,
We are using NFC on nRF52840 (Type 4 Tag, SDK15.0.0, Softdevice6.0.0) to exchange some data and we would need to be able to do the following, please let...
Hello everyone. I am using micropython to program on nrf52840 DK.
This is tutorial which i read https://circuitpython.readthedocs.io/en/latest/ports/nrf/README.html .
...
Segger provides great information for the use of the JTrace for tracing and profiling with the NRF52 development kit here.
https://wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52832...
Hi,
I'm expecting using a custom board with nrf52832 running connectivity program as a host to connect to the perpheral, and the hrc v5 example of pc-ble-driver is used...
hello support team
I am trying SDK Proximity coexistence example
I am using Mesh SDK 2.2
and nRF5_SDK_15.0.0_a53641a
I followed the steps given in link
I am getting...
Hi All,
i am working on SDK-14.2, i am facing issue with ble disconnection in dfu mode.
by using nrf-Connect in mobile i am upgrading the firmware, but it lost connection...
Details:
nRF52832
SDK 14.1 with matching SD
Compiling with GCC
I am trying to solve the following problem:
My device is powered by a coin cell (Manganese dioxide...
Hi, when my program calls sleep_mode_enter(), it enters system off (deep sleep) as expected. However, when I press the button on the Thingy52 to wake up, the bootloader starts...
I have problems connecting to a NRF51802 via stlinkv2 and openocd. I also tried a black magic probe flashed onto the blue pill board. Both did not work. I have ordered a NRF51822...
SDK 15.2
The nrfx_uarte_event_t callback contains a nrfx_uarte_xfer_evt_t; structure,
this structure has the bytes field as a uint8_t this should be a uint16_t to support...
Hi,
I'm using nrf52dk and SDK v15.
In my application, I have 2 input pin and I want to disable one of them when in one of the 2 pins occurs the event low to high, is it...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
