Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
Hi All,
I am using nRF51822 for my application.
how to change the App timer Interval dynamically means i have to change the timer interval before timeout.
sdk132. nrf52832 board
Try tutorial "Development with GCC and Eclipse" devzone.nordicsemi.com/.../
.
All the time I'm persecuted by error
/// *** No rule to make target...
I hava a BLE device which can be found by andrioid 4.4 and 6.0 smartphone, but cannot be found by apple iphone5s iOS 9.3, what could be possible wrong with it?
Hello all,
I am using the pc-ble-driver-py python bindings (which depends on pc-ble-driver) to test my BLE peripheral
It works fine for reading and writing characteristics...
Hi,
I use the Current Time Service to get back the time from a smartphone to have a real time clock with a timer.
On the current time service example, the value is read...
Hi:
I compiled the ble_app_cts_c project of the SDK12 using the Segger Embedded Studio having as target the PCA10040 board (S132 stack). After spending some time to convert...
follow the tutorial I'm stuck in the step of removing "retarget"
I don't have such option
I have this one. Should I just remove retarget.c directly via context menu...
main.c Hi,
Currently I am using "ble_app_uart" base example to understand how ble works. I have gone through bsp and other header that related to button events.
There...
Hello developers,
I am trying to use ble_hrm service example with actual heart rate from the module pulsesensor.com ( http://pulsesensor.com/ )
I am able to read raw data...
Hi,
I am working on one application in which I want to change pin number assign to channel 7 of SAADC in nrf 52. I am using Rigado BMD 300 module in my application. As...
Hi,
i want to use a current time service in nordic app (nRF Toolbox) for the bgm profile.
I see, that when the cts service is not found, the micro reset. Why?
Someone...
