Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I am trying to do a GPIO operation every one second repeated in 51822. I am using app timer to get this work done. The current average consumption is 45uA/H. The handler...
The blinky_freertos example in the nRF5 SDK 11.0.0, built for the nRF52 (PCA10040) with GCC, appears to work fine right out of the box. However, when I added -DDEBUG_NRF to...
Hi,
Is it possible to communicate directly between nrf51dk(peripheral) and PC(master)?
With UART communication, I need to connect a board to the PC via USB. But I want...
We are using the nrf51822 with softdevice 7.0.0 and BLE.
We have noticed cases where sd_temp_get never returns and the processor resets due to watchdog timeout.
Under...
Hi Sirs,
I have 2 modules in Mass Production by using nRF51822QFAA & nRF52832QFAA.
Customer asking us to support Apple Home Kit.
Can get your advise for :
How to...
Hi Nordic Tech Support!!!
Greetings of the Day!!!
I'm Dinesh Katkar, we team working on wearable IoT design and we need to interface 4 RGB LED-SMLP34RGB2W3 from nRF52832...
Hi：
1： NRF52832 How to set up the TX transmission power.
ble_app_hrs ：didn't see set TX transmission powe
2、NRF52832 ：How much is NRF52 maximum rate, how to set
THS...
What are the certifications required for Australia? My device has FCC and CE certifications, are these enough to allow someone to import my device? We are both really unsure...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I'm going to create a system where I do an SPI read from two sensors every 6ms. From these sensors I will get 20B each over SPI...
I'm writing a program sending die temperature data through BLE. I'm trying to combine the nrf51822 Heart Rate Monitor example and the nrf6310 Temperature example. Both examples...
Hello,
I have connected a SX1272 module to a nRF51 Development Kit using the Arduino connectors. Anybody written a sample app to get me going?
There is a SX1276 Ping Pong...
Hi all,
We have implemented the wireless mouse example on some custom hardware and it works great. We need to do something a little different however, and send absolute...
I can run peripheral examples in SDK folder like GPIO, Timer, Scheduler ...
but when I want to Add somethings like GPIO to peripheral_UART_ble or timer or scheduler It didn...
Hi Nordic Community,
I am using the nRF51822 to receive a data stream from the SPIS module and transfer the data directly to a phone over BLE using the S130 softdevice...
This is a follow-up question to devzone.nordicsemi.com/.../
I am using SDK_11 s130 on nRF51-dk.
I discovered that on nRF-UART Android app, notifications are not enabled...
