Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile).
Here is what I need;
The iOS and...
Hi,
Question regarding blog from Thomas Søderholm ( blog.nordicsemi.com/.../which-technology-should-i-choose-to-connect-my-wearable-device-to-a-phone):
Can't you do...
Keil 5.18a forces me to install "missing Software Pack"
I am trying to set up SDK 11, SD312, with Keil 5.18a, but when I try to load an example from the SDK 11 examples folder...
Hi! I have a nrf51 that act as a central and a beacon that is my peripheral, they connect to each other using is_uuid_present but I can't enable notification using db_discovery...
Hello,
I am currently designing a PCB containing the nRF51822 chip and I am concerned about how I will be able to update the program.
I have 2 main questions :
I...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
When I add a GATTC in S110-V6.0.0 ,my GATTS stops working,the NRF Master control panle retern ERROR(0x85):GATT internal ERROR Error(0x85):GATT ERROR .Can S110-V6.0.0 run GATTC...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
Hey ,
I'm trying to implement a device that waits for the clicks from the user and sends it over ble as notifications.
i have written the header files for sensor . and from...
im trying to get my nrf51822 connecting only to my phone, I set the phone mac address on white list, but I cant connect to my phone (android) wiht nrf master control.
How...
