after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
HI：
I found a amazing problem:My flash project is ok,and my BLE project is ok too; But when i need to write data to flash,the BLE can't work any more.
code as follow:
all_init...
I'm using nRF51 SDK 6.0.0 and wanted to know when an "advertisement packet received" event is posted to the application. It looks like within a scan window only one such event...
Hi there,
I just ordered a nRF52 Preview DK and was wondering if this series will also be compatible with the nRF51 IoT SDK?
Anything I should be aware of beforehand...
I have an nRF51822-based device, which is a peripheral running the Soft Device s110. It has some vendor specific (custom) characteristics that are read/write. A mobile app...
Hey Nordic,
I am using the nrf51 to operate a sensor and send data wirelessly. I want to store the id of the sensor in the flash memory and I Understand that a good way to...
Hi, as I tried out the example code for PWM in SDK 9, it didn't worked for me. A closer look showed that in method app_pwm_init the method app_pwm_channel_duty_ticks_set will...
I have a peripheral (nRF51822, s110, SDK 8.1, using the device manager) which should only ever be bonded with zero or one centrals. The behaviour I'm aiming for is this: ...
Has anyone interfaced the nRF51822 to the CC3000 Wireless chip? I have started implementing the host controller functions in nRF51822. It would help me jump start if anyone...
I try to capture a BLE connection with the nRF Sniffer.
I can see the advertisement packages, but after i established a connection from an andriod device i didn't get any...
I want to drive motors at 40kHz and am wondering if I will be able to do this with the nRF51822. If not 40kHz, I might be able to go as low as 15kHz. What is the resolution...
Hi, I am using nrf51822 ble module. I want to have multiple such modules which could connect to a central device. How could I make it that the central device encourages only...
Hi, I am creating a custom service and corresponding characteristic. For that I am planning to use bluetooth base uuid (for confirmation : 0000 0000 -0000-1000-8000-00805F9B34FB...
Hi,
I`m working on our firmware for nRF51822 and I received the assert from soft device when turning off the global interrupts for our time-dependent procedure which have...
I am using PCA10001 board.
First of all i am unable to find nRF51 SDK.exe.
So i downloaded SDK form below link
link text
I changed device to nRF51822_xxAA.
Now i...
Nodic Semicond has made a nice step-by-step description for how to fix a corrupted infoPage.
It involves starting nRFgo Studio from a command prompt with "-defaultsettings...
