Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello Nordic Community,
i have the following issue, im using a Nordic Nrf51422 in proprietary mode. On my RSA i can see that before the paket sending begis the radio sends...
Today, I tried out the Ble Bootloader from the Sdk examples.
As a central client, I'd used the »nRF Loader App« an an iPhone and also »nRF Mcp« on an Android Tablet.
I...
Hi,
from Keil uVision I need to debug/program nrf51822 in my application which uses 1.8 V. I guess nrf51 DK is not capable of doing this (it supports only 3 V targets). What...
Hi,
I have a reset issue when trying to set a delay greater or equal to 100 milliseconds using nrf_delay_ms(...). This only happens if I start my app timers (app_timer_start...
Hi,
I am trying to generate a 128Hz sine wave using the nrf_pwm library . First I tried this with SD110 enabled but ran into some problems that turned out to be a known...
Hi,
I'm going through the errata and a few of them look serious that the developer kit might be useless for some of us if we want to use it for any realistic testing (I...
I am trying to add a static passkey to my peripheral and protect from MITM. I tried the example nRF51-ble-app-uart-static-passkey but it doesn't seem to work correctly.
...
Hi,
I am new to nordic n51822, i have implemented adc and timer independently.
Now, what i want to do is read the adc values on a specific time when the timer overflows...
Received my nRF52 preview board yesterday and have been battling to get my S130 based nRF51 code running on it with the S132 soft device (the code is here: github.com/......
The codes i am using is
nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral and nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_peripheral\ble_app_hrs
From the peripheral...
Just getting started with the PCA10001. I can compile if I select the device nrf51822_xxaa_s110, but when I load it tells me "can't load flash device description".
It subsequently...
I have take the basic ble_app_hrs_with_timeslot and modified it to calculate the timing of subsequent calls to the timeslot START event.
Specifically,
take note...
Hello,
I'm trying to get the new SDK up and running on my OSX machine. I would like to make the blinky example work on my PCA10003. So, I copied the blinky/pca10028 folder...
Hello, Do you guys know if it is possible to generate a stable 38kHz signal using the Nordic?
I have been able to generate the required frequency however I am observing...
