Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
My application seems to be running out of memory, now I received NRF_ERROR_NO_MEM from sd_ble_gap_ppcsp_set. I don't understand why this has started since I don't think i...
Im using custom board with nRF8001. I'm using Hello World example from GitHub.
The nrf chip revision is C not D. When I connect the board to Arduino Leonardo the device start...
Hi
I ran the example " ble_app_hrs ". the consumption is 1.5mA, when I hold SWCLK and nRESET low,the consumption is fall to 0.9mA. how I could reduce the consumpion??
I can input "hello" in win8.1 with button 0
==
before text in iphone5
I change
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(16, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
Hello,
I am searching for an exampleproject to learn how to connect to motherboards (or an evaluation board)
over bluetooth:
I try to send data from on chip (nrf51822...
It seems that is not possible to rewrite data on a block ?
I want to persist some data. The first time (after erasing all the flash memory) I store a data on a block, it...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Hi all,
I noticed that there are some instructions for testing keyboard on win8.1 or USB dongle.
Can I test it on my iPhone5s which is iOS7.0.4 now?
Regards,
Aaro...
when I use nRF51822 ESB Protocol,I set retransmit delay = 600us,anything else is working
good,communication is very well,but the minimal Tx period is 1.2ms,not 600us,why...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
I want to generate a pulse signal with PPI, timer2 and gpiote. But it doesn't work. Anything wrong with my code?
void init_timer1()
{
NRF_TIMER1->PRESCALER = 1;
NRF_TIMER1...
I'm working on a product that integrates an nrF51822 talking over SPI to an external display. The display protocol involves a series of alternating 10 us sleeps and SPI sends...
