Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi All,
I have integrated DFU service into my application. I am successfully able to use OAD so far. Today I have added a piece of code to my application. So, my binary...
While doing power profiling on Adafruit's nRF52 Arduino port, I have noticed that when using delay(500), the CPU power consumption goes up about 1ms before actually returning...
Hi,
I have a project where I am wirelessly streaming 16bit mic data at fs=50,000. I'm receiving that data on another nRF52840 dev board. I've ensured that the data doesn...
Hello,
I use the nRF24LE1-32 develop a product. It has strict requirements for low power consumption.Now I get 10-20uA current on deep sleep mode referring to the article...
I'm trying to pair my device (nRF82382) to nRF Connect (Dev Kit) and using another Dev Kit as a BLE_Sniffer. I'm trying to establish Pairing with LESC enabled. It's Pairing...
Hi community ! All is in the title.
The latency between sending the message and receiving the callback is not stable ( between 1600 & 4300 ms) I know that this delay is...
Hello, guys!
We are currently developing our firmware with nRF9160-DK and nRF Connect SDK v1.3.0. Among the other things, we need to communicate with the ultrasonic sensor...
Hi,
As we are in design phase of our custom board based on nRF9160, can you please let us know what all pins needs to be exposed in our design for collecting modem traces...
Hi Team,
I am trying to integrate a scheduler feature for my Thingy 91 using a nRF9160 DK kit. I searched for a few examples and found the one below in the link:
https...
Hello everyone,
I am developing a simple BLE node with an I2C sensor on it. Basically I just need to send over BLE the measurements made by that I2C sensor every minute...
Hello,
I am new to the Nordic environment and am trying to set up a beacon to scan and advertise using BLE.
I used the beaconing example ( https://github.com/NordicSemiconductor...
Hi, I have the same issue as in here: https://devzone.nordicsemi.com/f/nordic-q-a/62676/2-spi-devices-nordic-nrf52382 but for me the Debug/Release-toggle does not work. I...
Hi,
Can you confirm if TWI is supporting I2C clock streaching? Or and workaround to handle such a case.
As in attached picture is slave device requirements. Slave device...
Hello,
I’m using keil compiler.
My configurations are nrf51822ac/SDK12.3/s130_nrf51_2.0.1_softdevice.
I’m trying to migrate to SEGGER studio.
I’m referring to the...
In my case, I have 50+ devices as sensor and advertising measurements every 10 seconds, ADV_DURATION = 120s, use the 1E FF manufacturer data and self defined payload protocol...
