Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello, I want to make periodically wake up nRF52840, performing some work (connecting to MQTT broker, sending some data) and after that going to low power mode. Then the nRF52840...
Hello,
We want to use a nrf52840 as a logic controller which reads data from Modbus RTU Sensors (as Modbus RTU Master) and simultaneously is the Modbus RTU Server for an...
Hello Team,
We are trying to make Release and Debug mode for our software.When I compile a sample program I see lot of Debug information in the Mapfile. Will this influnce...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hello,
When building my project although the terminal doesn't show me using all the RAM, I get the following error message which fails the build.
I am using a...
Hello,
I was working on a ble communication using two nrf52dk boards while one of the two stop responding. The board is correctly recognised by the computer and segger asks...
When I am on to collect the accelerometer data from Thingy-53, only 3 sampling frequency options are provided which are 20 Hz, 62.5 Hz and 100 Hz as shown in figure. Please...
I am new to nRF chips and currently working with the nRF52810. I am developing with nRF Connect SDK and VSCode.
I have encountered an issue with the Blinky example (ncs...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Running the Ciphersuites sample code on the nRF9161 I get Connection Refused on all attempted ciphersuites. Including after adding the CONFIG_EXTENDED_CIPHERSUITE_LIST=y to...
Hello,
Dev board: nRF52840 development board.
OS: Zephyr (NCS v2.6.0).
My requirement and What I am using...
- I want to perform DFU for application core & bootloader...
Hello Nordic Team, I am using nRF5340-DK and I have a PPK-2 for current measurements. My development environment is NRF Connect SDK v2.5.2. I used https://infocenter.nordicsemi...
Hello,
I am using the "direction finding connectionless beacon sample" to test various settings of the beacon. About setting parameters, I have the following two questions...
Hi. I'm working on a BLE system with Central and Peripheral with nRF5340 with 70msec of CONN_INTERVAL and about 1sec of SUP_TIMEOUT. The Central unit also has a UART that...
