Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi all,
I'm a beginning hobbyist with nRF52. I'm programming a BC805m using my nRF52-dk and nRF Connect SDK v1.9.0 (zephyr & Segger Embedded Studio).
The learning curve...
Hi, I am new to nrf.
I want to interface Sparkfun capacitive fingerprint sensor with nrf52832.
There is Arduino lib is present for this module.
But I am stuck on how...
1. When I start the SEGGER Embed open project: when 10_hello_world_clock_gettime, the following pop-up error pops up: Did not finish 'cmake',
2. When I close the window...
In nRF Connect SDK 1.7.1, how to send hex data over the connection by AT#UDPSEND?
I use AT#XUDPCLI to create UDP client and connect to server.
For the AT#UDPSEND, it seems...
Hi,
1. How do I resolve this error?
2. waring line 93->line 165
3. error : line 104,line114, line128,line 138,
Thank you for all your assistance. Kind regards, Peter...
Hi,
ncs v1.9.1
dk: PCA10090 0.9.0
example :serial_lte_modem
Does this example have the following capabilities?
1. The hex data received from the server in EDRX...
Using the UART example of the 52DK with the TX and RX pins set as 8 and 6 the example works. If I try to change the pins to different pins such as 22 and 23, it does not work...
Hi,nordic
I'm looking for L2CAP Connection Oriented Channels example in NCS,such as Object Transfer Service.
can you tell me some information？
Thanks.
TRANSLATE...
Hi everyone, i would like to put this topic here so that new developers can benefit from it i hope.
when you want to measure the current you need a PPK-2 or Oscilloscope...
Hi expert,
I use the example below:
D:\Nordic\nRF51 SDK\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart
I changed UART pin from default pin0.08 and pin...
My goal is to implement dynamic pairing and connection to a Bluetooth device based on SDK16.0.0 and s132_7.0.1, and add a buttonless DFU function. By sending instructions...
I am trying to integrate GitHub - NordicSemiconductor/IOS-DFU-Library: OTA DFU Library for Mac and iOS, compatible with nRF5x SoCs library in one of the SwiftUI mobile application...
I was starting from multi-NUs.I need to send form a Master a message to 4 Slave every 50mS.
I see that up to 100ms It work but that at 50mS the comunication doesen't work...
Hello,
I was given a project that was built using nRF Connect SDK 1.6.0. I tried installing nRF Connect SDK 1.9.1 but received a bunch of compiler errors when building the...
