I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
it's a nice concept to include sensors via the device tree and simply enable them in the project file. But I feel like I'm losing control of the sensor a bit. I don...
Hello nordic. I've been using the PPK2 to measure the current draw of the nRF9160DK. However, spi peripherals are not included in these measurements. I was told that if you...
Hi
I´am pretty new with the nRF connect sdk. I want to check the features from BLE long range /coded phy.
In the past I have allready worked with the ble_att_mtu_throughput...
hello Sirs
How can I put nrf5340-sdk in to extended mode to transfer 250 bytes of data over BLE radio?
the sample code I am using is Peripheral-uart example code.
Excuse me:
I want to implement nrf52833 run FreeRTOS，The nRF52840 project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos\pca10056\s140\ses can only...
Hello All,
I am using NRF52833 in my project. I am also using RTOS in the code. I was previously working on NRF52840 but now I have migrated to NRF52833. I have changed...
I'm new to using NFC.
I've tried downloading a few NFC sample programs to my nRF5340-DK board and playing around a bit, but I ultimately want to implement something like...
We are using nordic SDK 16.0.0 and mesh SDK 4.2.0 with a nRF52840 chip.
Our products already have the provisioner/provisionee and config client/server implemented, based...
Hello, I use nrf9160dk, ncs v1.6.1.
I'm trying to use both AWS IoT to store some data from the DK board, and to connect to nrfcloud for AGPS data. I don't have any previous...
Hi All,
I am beginner in development on Nordic product.
I am using sdk v1.5.1 and nrf5340 for development.
I want to add open source library libcorrect.a for Forward...
Hi.
i use
i call i2c_write() and if the buffer is large(8kB) i get error in i2c transfer -5.
i go deeply and found that it is due too error -11:
If i step into...
hi, I am new to Nordic development, and I have to write a VC# Windows App to connect with a BLE GATT oximeter (based on an nRF SOC) through nRF52840 dongle in a few days....
Hello,
I am designing a set of equipment, one to transmit voice and the other 200 to receive voice (One person speaks and 200 people listen). It is 8kByte/s low-quality...
