I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
We have a device that we are trying to implement an encrypted data transfer on. We wanted to lock down all the characteristics until we write a passkey on our security characteristic...
Hi there, I am trying to change the transmission power of the NRF5340 devices (for IEEE 802.15.4 radio) with Contiki-NG. With some other hardware (sky motes) that is based...
Hi,
Using Power Profiler v3.3.0 with PPK2 on Chrome on MacOS.
The screenshot action results in a chopped image. See the top part is missing?
When I remove (by commenting...
Hi,
I'm trying to interface to a third-party 802.15.4 RF chip using an nRF52833, where the received packets from the remote device have enabled AES-CTR encryption.
I started...
Hello everyone,
I am looking at the init structure of the NRF52832's RTC and I cannot find any explanation on the "reliable" variable.
I can see its usage in the driver...
Hi,
I have an application for the nRF9160 where I want to use mcuboot and of course signing, but I get the following message while building, that my key file is invalid...
Hello, I'm trying to use the nRF52DK development kit as a Bluetooth sniffer. after following your "nRF_Sniffer_UG_v2.2.pdf" guide, all I see in Wireshark are advertising messages...
Hello, I want to know how I can print console messages out over the COM ports that the Thingy:91 exposes using the nRF Connect SDK. I'm able to see the com ports but I'm unable...
Hi,
any suggested way to utilize nRF52840 dongle as a wireless (BLE) connectwion between multiple ARM linux embedded computers (nodes) ?
nRF52840 would be utilized from...
I was just thinking whether the below set of lines could be a solution to the problem faced in this case https://devzone.nordicsemi.com/f/nordic-q-a/83358/light_bulb-example...
Hallo,
I am really new with the SPI communication. I am just trying to read the registers from the MAX31865 using nRF52840. Is there any helpful example code available?...
I found app_timer2 library very interesting and I want to use it in our main application code but before that I am exploring it.
I wrote this code and it's not working,...
Hi I try to build the sample
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.7.1/zephyr/samples/net/sockets/can/README.html
but i get this this error.
*** Booting...
Hi DevZone !
I am currently trying to migrate from nRF52840 to nRF52833 because of a backorder problem with the former.
My application consist of a Mesh configurations...
Hi all,
I am working on interfacing 2 SPI sensors ADXL362 and ADXL372 for learning purposes. Following is the overlay created for the same.
refering this https://devzone...
